Mic Test
Check your microphone in a few seconds — a live level meter, the sample rate it delivers, and a short recording you can play back. The sound never leaves your device.
Check your microphone in a few seconds
Your browser will ask for permission. The sound is measured on your device and nothing is sent anywhere.
The list fills in once access is allowed — browsers hide device names until then.
Voice processing
On is what a video call uses. Turn them off to hear the raw input.
Table of contents
How to test a microphone online
- 1
Press Start and allow the microphone
The browser asks only when you press the button. Once you allow it, the device list fills in with your microphones' real names, so you can switch if the wrong one opened.
- 2
Speak normally and watch the meter
Talk at the distance and volume you would on a call. The words above the meter tell you whether the level is too quiet, good, loud or clipping; the thin marker holds the loudest recent peak.
- 3
Record and listen back
Press Record, say a sentence, and play it back. This is the only way to hear what other people hear — the meter tells you how loud you are, not whether you sound muffled, echoey or robotic.
- 4
Try the processing switches
Echo cancellation, noise suppression and automatic gain are on by default, as they are on a video call. Switch them off and record again to hear what your microphone picks up on its own.
What the readouts mean
The level is the RMS — the average power — of the last few dozen milliseconds of sound, in dBFS. RMS follows how loud speech feels, which is why the bar moves smoothly rather than flickering on every consonant. The marker is the loudest single sample, held for a second and a half and then allowed to fall, because peaks last only a few milliseconds and you would never see them otherwise. When that marker turns red the input has reached full scale and is clipping.
The frequency bars split the sound into bands spaced by octaves, low on the left and high on the right. A voice fills the left half and middle; a hum at the far left that never goes away is mains interference or a fan, and a microphone that shows almost nothing on the right sounds muffled. If you have asked your system to reduce motion, the bars update a few times a second instead of continuously.
Sample rate and channels are what the browser reports for the open microphone. 48 kHz is normal; 44.1 kHz is common on Macs and USB microphones. Mono is normal too — most built-in and headset microphones are a single channel, and calls are mono anyway. Not every browser reports these; where it does not, the audio engine’s own rate is shown instead.
Echo cancellation and noise suppression show what is actually in effect, which is not always what you asked for: some devices and browsers refuse to turn processing off, and the readout says so.
When the meter does not move
If it says no signal, the browser opened a microphone but heard nothing. Check for a mute switch on the headset or its cable, and pick another device from the list — laptops often have a disconnected line input listed as a microphone. On Windows, open Settings → System → Sound, choose the input and check its volume is not at zero. On a Mac, System Settings → Sound → Input shows its own level meter and input volume.
If access was blocked, allow it from the icon at the left of the address bar in Chrome and Edge, the crossed-out microphone in Firefox, or Safari → Settings → Websites → Microphone. Then check the operating system: Windows Settings → Privacy & security → Microphone, including “Let desktop apps access your microphone”, and on a Mac, System Settings → Privacy & Security → Microphone, with your browser switched on.
If the wrong microphone opens, choose the right one from the list here. To change what every site uses, set the default in your browser’s site settings (Chrome and Edge let you pick a default microphone) or in the operating system’s sound settings. Plugging in a headset after the page is open adds it to the list automatically.
If it says the microphone could not be opened, another program may have exclusive use of it — some audio interfaces and call apps take it over. Close them, or turn off “Allow applications to take exclusive control” in the device’s Windows sound properties, and press Start again.
Frequently asked questions
For speech, aim for the meter sitting around −30 to −20 dBFS while you talk, with peaks reaching about −12 to −6. Below −45 most of the time and you are too quiet; peaks touching 0 dBFS mean the signal is clipping, which sounds harsh and cannot be fixed afterwards. Automatic gain, on by default, nudges the level towards a sensible range for you.
Decibels relative to full scale. 0 dBFS is the loudest value the audio can hold, so every real reading is negative, and every 6 dB down is roughly half the amplitude. It is the only honest unit a web page can show: the browser has no idea how sensitive your microphone is, so it cannot tell you the sound level in the room.
A meter measures loudness, not quality. Record a few seconds and listen. Muffled sound is often the wrong microphone — the webcam's across the room instead of the headset's. A thin, telephone-like sound on Bluetooth headphones is the headset switching to its hands-free mode, which most do as soon as the microphone is in use. Echo and pumping usually come from the processing, which you can switch off here to compare.
Because the browser may resample everything to the rate its audio engine runs at, so the number shown is not always what the headset sends. Bluetooth hands-free mode carries narrowband audio, and you will hear that on playback — dull, with no high frequencies — even when the readout says 48 kHz.
No. The recording is made by your browser and held in the tab's memory as a temporary file that only this page can play. It is replaced when you record again and deleted when you leave the page. There is no upload button because there is nowhere for it to go.
On purpose. Sending your microphone straight to your speakers produces a feedback howl on any laptop, and a delay that makes it hard to speak. Recording and playing back gives you the same information without either problem.
For calls on speakers, yes — without echo cancellation the other person hears themselves. With headphones you can often turn it off for a more natural sound. Noise suppression removes fans and keyboard clatter but can make the voice warble; try both ways and listen to the recordings.
The Zeal Promise
Non-negotiable, on every tool we ship.
- No sign-up — ever
- No watermarks on any output
- No ads near the download button
- Works fully on mobile
- Privacy-first: processing stays in your browser
- Open source (MIT) — audit it, contribute, self-host
- Zero runtime dependencies in tool logic